(Items 5406 to 5985)

Last Updated (01/26/2004)

Click here to return to Index Page

Table Of Contents

SPECIFICATION REQUIREMENTS
1) Limits and/or locations to receive the placement of traffic buttons for texturing the finished surface of the shoulder must be shown on the plans.
2) The distance the traffic buttons should be placed from the outside edge of the edgeline shall be between 4 and 8 inches. This distance will be as specified on the plans or as directed by the Engineer.
3) The non-reflectorized traffic buttons will be of the class and/or type as specified on the plans.
4) The following Statewide Standard Details Sheet is required for the design details for textured shoulders using traffic buttons:

• ST(2)-99                Shoulder Texturing Using Pavement Markings

OPTIONAL REQUIREMENTS
1) When removal of buttons is required, it shall be in accordance with Item 677.

REFERENCE ITEMS
(672)

Go to Top

SPECIFICATION REQUIREMENTS
1) The length of the quad-corrugated beam weldment shall match the nominal width of the crash cushion (24", 30", or 36") as shown on the plans.
2) The width, type and the number of bays must be shown on the plans for the QuadGuard System.
3) Locations for the placement of the QuadGuard Systems must be shown on the plans.
4) Must include the following Statewide Standard Details Sheet for the fabrication and installation of the QuadGuard System:

• QUAD(N)-99                QuadGuard System (Narrow)
• QUAD(W)-99                QuadGuard System (Wide)

5) When moving and resetting temporary QuadGuard Systems, the new location of the QuadGuard System must be shown on the plans when either moving it from a stockpile and resetting it at a location on the highway or moving it from an existing location on the highway and resetting it at a new location on the highway.
6) When the QuadGuard System is no longer required on the project, it will be removed from the existing location on the highway and stockpiled at a designated location shown on plans or as directed by the Engineer.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(421)

Go to Top

SPECIFICATION REQUIREMENTS
1) The locations for the installation of crash-cushion attenuating terminals must be shown on the plans.
2) The following Statewide Standard Details Sheets must be included in the plans for the details and installation of the crash-cushion attenuating terminal:

• CATGR(1)-97 and CATGR(2)-97           Crash Cushion Attenuating Terminal Details (Guardrail) (2 sheets)
• CATCB(1)-97 and CATCB(2)-97           Crash Cushion Attenuating Terminal Details (Concrete Barrier)(2 sheets)

3) The following Statewide Standard Details Sheet must be included in the plans to show the details 
    of the object marker which shall be installed on the front of the terminal:

• D&OM(VIA)-98                Delineators & Object Markers for Vehicle Impact Attenuators

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(540)

Go to Top

5461 METAL THRIE-BEAM GUARD FENCE

SPECIFICATION REQUIREMENTS
1) Dimensions of posts shall be shown on the plans.
2) Locations of installations shall be shown on the plans.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(540)

Go to Top

SPECIFICATION REQUIREMENTS
1) The number of transportable cellular telephones (TCT’s) needed on a project will be as shown on the plans.
2) The type of TCT’s will be as shown on the plans or as approved by the Engineer.
3) To include this Item in a project, it must be added to the Specification List as a Reference Item to either Item 504, if a field office and/or laboratory is required on the project, or to Item 500.

PAYMENT AND MEASUREMENT
This Item will be paid for at the invoice amount plus five (5) percent.

REFERENCE ITEMS
None

Go to Top

SPECIFICATION REQUIREMENTS
1) The locations of the dead end barricades can be shown on the plans or as directed by the Engineer.
2) The following Statewide Standard Details Sheets is required (unless otherwise shown on the plans) for the construction and installation details of the dead end roadway barricade:

• WZ(DERD)-98                Work Zone Dead End Roadway Details

OPTIONAL REQUIREMENTS
1) When required by the plans, signs, sign supports and chevrons, will be paid for under Item 644, "Small Roadside Sign Assemblies"

REFERENCE ITEMS
None

Go to Top

SPECIFICATION REQUIREMENTS
1) Furnish and place as shown on the plans.
2) Gradation for coarse aggregate as shown on the plans.
3) Color shall be shown on the plans.
4) Surface pattern to be shown on the plans.
5) Specify thickness in pay Item description.
6) This is a plans quantity Item.

OPTIONAL REQUIREMENTS
1) When excavation and backfill are required, they shall be in accordance with Items 110, 132 and 400.

REFERENCE ITEMS
( 420, 421, 437)

Go to Top

SPECIFICATION REQUIREMENTS
1) Installation locations shall be shown on the plans.
2) All materials to be furnished by the Contractor shall be in accordance with details shown on the plans.
3) QuadGuard Elite System crash cushions shall be fabricated and installed in accordance with the manufacturer's shop drawings and details shown on the plans.
4) Details for the QuadGuard Elite System crash cushions and any necessary concrete support pads, including steel reinforcement and placement as required by the manufacturer.
5) Unless otherwise shown on the plans, any QuadGuard Elite System removed shall remain the property of the State.
6) Stockpile or storage location(s) shall be shown on the plans.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(421)

Go to Top

5699 - EPOXY AND ADHESIVES

SPECIFICATION REQUIREMENTS
1) The locations for Epoxy and Adhesives will be of the type noted on the plans or approved by the Engineer.

OPTIONAL REQUIREMENTS
None

PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.

REFERENCE ITEMS
None

Go to Top

5762 - MODULAR GLARE SCREENS FOR HEADLIGHT BARRIER

SPECIFICATION REQUIREMENTS
1) The locations for Modular Glare Screens for Headlight Barrier will be of the type noted on the plans or approved by the Engineer.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
None

Go to Top

5764 - ANTI-GRAFFITI COATINGS

SPECIFICATION REQUIREMENTS
1) The locations for Anti-Graffiti Coatings will be of the type noted on the plans or approved by the Engineer.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(427)

Go to Top

5785 - REMOVING AND RELOCATING/RESETTING SINGLE GUARDRAIL TERMINALS

SPECIFICATION REQUIREMENTS
1) The locations for Removing and Relocating/Resetting Single Guardrail Terminals will be of the type noted on the plans or approved by the Engineer.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(540)

Go to Top

5786 - RAISING METAL BEAM GUARD FENCE RAIL ELEMENTS

SPECIFICATION REQUIREMENTS
1) The locations for Raising Metal Beam Guard Fence Rail Elements will be of the type noted on the plans or approved by the Engineer.

OPTIONAL REQUIREMENTS
1) When galvanizing has become scratched, chipped or otherwise damaged, it shall be repaired in accordance with Item 445.
2) When the Contractor is required to furnish new rail, it shall conform to the requirements of Item 540.

REFERENCE ITEMS
None

Go to Top

5788 - LANDSCAPE PAVERS

SPECIFICATION REQUIREMENTS
1) The locations for Landscape Paving will be of the type noted on the plans or approved by the Engineer.

OPTIONAL REQUIREMENTS
1) When subbase material is required, it shall meet the requirements of Item 247.

REFERENCE ITEMS
(421)

Go to Top

5819 - SINGLE GUARDRAIL TERMINAL

SPECIFICATION REQUIREMENTS
1) The locations for Single Guardrail Terminal will be of the type noted on the plans or approved 
     by the Engineer.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(540)

Go to Top

5840 - TRINITY ATTENUATING CRASH CUSHION SYSTEM

SPECIFICATION REQUIREMENTS
1) The locations for Trinity Attenuating Crash Cushions shall be as shown on the plans.

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(421, 440)

Go to Top

5866 CURB RAMP AND LANDING

SPECIFICATION REQUIREMENTS
1) The locations for Curb Ramp and Landing be as shown on the plans.
2) Concrete for extruded construction shall be Class "A" unless otherwise shown on the plans.

OPTIONAL REQUIREMENTS
1) When required, removal and disposal of existing concrete will be in accordance with Item 104.

REFERENCE ITEMS
(360, 420, 421, 437, 440, 526)

Go to Top

SPECIFICATION REQUIREMENTS
1) The finished Surface of the Pavement shall be smooth and true to the established line, grade and cross section shown on the plans.
2) Surface Test Type B shall apply longitudinally along the finished riding surface of all travel lanes unless Surface Test A is shown on the plans. When shown on the plans, Surface Test Type B shall apply longitudinally along the finished riding surface of all travel lanes except service roads or other excluded areas. Surface Test Type B may be required on service roads and other areas excluded by the specification if called for on the plans.

OPTIONAL REQUIREMENTS
None

PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.

REFERENCE ITEMS
None

Go to Top

SPECIFICATION REQUIREMENTS
1) The locations for the installation of box beam bursting energy absorbing terminal--single-sided crash cushion must be shown on the plans.
2) The following Statewide Standard Details Sheets must be included in the plans for the details and installation of the single-sided crash cushion:

• SSCC-03           Single Sided Crash Cushion Details (BEAT-SSCC)

3) The following Statewide Standard Details Sheet must be included in the plans to show the details 
    of the object marker which shall be installed on the front of the terminal:

• D&OM (VIA)-98                Delineators & Object Markers for Vehicle Impact Attenuators

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(658)

Go to Top

SPECIFICATION REQUIREMENTS
1) The locations for the installation of REACT 350 must be shown on the plans.
2) The following Statewide Standard Details Sheets must be included in the plans for the details and installation of the REACT 350:

• REACT (N) -03           Reusable Energy Absorbing Crash Terminal (Narrow REACT 350) (2 sheets)
• REACT (W)-03           Reusable Energy Absorbing Crash Terminal (Wide REACT 350)

OPTIONAL REQUIREMENTS
None

REFERENCE ITEMS
(421)

Go to Top