1993 Statewide Special Specifications
(Items 6001 to 6995)
Last Updated (01/27/2003)
Click here to return to Index Page
Table Of Contents
ITEM NO. - TITLE AND REQUIREMENTS
6001 - DIGITAL LOOP VEHICLE DETECTOR UNIT
SPECIFICATION REQUIREMENTS
1) The locations for Digital Loop Vehicle Unit will be of the type noted on the
plans
or designated by the Engineer.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
None
Go to Top
6002 - FLASHER CONTROLLER ASSEMBLY
SPECIFICATION REQUIREMENTS
1) The locations for Flasher Controller Assembly will be of the type noted on
the plans
or designated by the Engineer.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
None
Go to Top
6003 - VEHICLE LOOP WIRE SEALANT
SPECIFICATION REQUIREMENTS
1) The locations for Vehicle Loop Wire Sealant will be of the type noted on the
plans
or approved by the Engineer.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
None
Go to Top
6004 - THREE CONDUCTOR NEUTRAL SUPPORTED SECONDARY CABLE
(TRIPLEX)
SPECIFICATION REQUIREMENTS
1) The locations for Three Conductor Neutral Supported Secondary Cable (Triplex)
will
be of the type noted on the plans.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
(680)
Go to Top
6005 - PROGRAMMABLE SIGNAL HEADS
SPECIFICATION REQUIREMENTS
1) The locations for Programmable Signal Heads will be of the type noted on the
plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Programmable Signal Section" |
EA |
REFERENCE ITEMS
None
Go to Top
6007 - ROADWAY LIGHTING ON TRAFFIC SIGNAL POLE
SPECIFICATION REQUIREMENTS
1) The locations for Roadway Lighting on Signal Pole will be of the type noted
on the plans.
2) Poles and mast arms for roadway lighting on traffic signal poles will be paid
for under Item 686.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Roadway Lighting on Traffic Signal Pole" |
EA |
REFERENCE ITEMS
(610, 620, 628)
Go to Top
6009 - ROADSIDE FLASHING BEACON ASSEMBLIES
SPECIFICATION REQUIREMENTS
1) The locations for Roadside Flashing Beacon Assemblies will be of the type
noted on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Roadside Flashing Beacon Assemblies" |
EA |
REFERENCE ITEMS
(441, 442, 445, 446, 447, 449, 618, 620)
Go to Top
6010 - SALVAGING TRAFFIC SIGNALS
SPECIFICATION REQUIREMENTS
1) The locations for Salvaging Traffic Signals will be of the type noted on the
plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Salvaging Traffic Signals" |
EA |
REFERENCE ITEMS
None
Go to Top
6011 - TEMPORARY LIGHTING SYSTEM
SPECIFICATION REQUIREMENTS
1) The locations for Temporary Lighting System will be of the type noted on the
plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Temporary Lighting System" |
LS |
REFERENCE ITEMS
(618, 620, 622, 624, 627, 628)
Go to Top
6012 - REMOVING AND REPLACING ROADWAY
LUMINAIRES
SPECIFICATION REQUIREMENTS
1) The locations for Removing and Replacing Roadway Luminaires will be of the
type noted
on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Removing and Replacing Roadway Luminaires" |
EA |
REFERENCE ITEMS
(610, 616, 618, 620)
Go to Top
6013 - STEEL MAST ARM POLE ASSEMBLIES FOR
SIGNS
SPECIFICATION REQUIREMENTS
1) The locations for Steel Mast Arm Assemblies shall be as shown on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Steel Mast Arm Assemblies for Signs" |
EA |
REFERENCE ITEMS
(686)
Go to Top
6014 - REMOVAL, TEMPORARY RELOCATION AND
PERMANENT
REINSTALLATION OF SIGN
ASSEMBLIES
SPECIFICATION REQUIREMENTS
1) The locations for Removal, Temporary Relocation and Permanent Reinstallation
of Sign
Assemblies will be of the type noted on the plans or as
directed by the Engineer.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Removal and Reinstallation of Sign Assembly with 12
Inch Foundations" |
EA |
2) |
"Removal and Reinstallation of Sign Assembly with
24
Inch Foundations" |
EA |
REFERENCE ITEMS
(646, 647, 656)
Go to Top
6015 - REMOVING OVERHEAD SIGNS
SPECIFICATION REQUIREMENTS
1) The locations for Removing Overhead Signs will be of the type noted on the
plans or as directed
by the Engineer.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Removing Overhead Signs" |
EA |
REFERENCE ITEMS
None
Go to Top
6016 - REMOVING OVERHEAD SIGN LIGHTING
FIXTURES
SPECIFICATION REQUIREMENTS
1) The locations for Removing Overhead Lighting Fixtures will be of the type
noted on the plans
or as directed by the Engineer.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Removing Overhead Sign Lighting Fixtures" |
EA |
REFERENCE ITEMS
None
Go to Top
6017 - REMOVING AND RELOCATING OVERHEAD SIGN BRIDGES
SPECIFICATION REQUIREMENTS
1) The locations for Removing and Relocating Overhead Sign Bridges will be of
the type noted
on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Removing and Relocating Sign Bridges" |
EA |
REFERENCE ITEMS
(416)
Go to Top
6018 - STRENGTHENING OVERHEAD SIGN SUPPORT STRUCTURES
SPECIFICATION REQUIREMENTS
1) The locations for Strengthening Overhead Sign Support Structures will be of
the type noted
on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Strengthening Overhead Sign Support
Structures" |
EA |
REFERENCE ITEMS
(441, 442)
Go to Top
6019 - REMOVE AND INSTALL EXISTING SIGN PANELS
SPECIFICATION REQUIREMENTS
1) The locations for Remove and Install Existing Sign Panels will be of the type
noted on the plans.
OPTIONAL REQUIREMENTS
1) When new sign lights are required, they shall be in accordance with Item 652.
2) When new sign walkways are required, they shall be in accordance with Item
654.
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Remove and Install Existing Sign Panels
(Overhead)" |
EA |
REFERENCE ITEMS
(634, 636, 642)
Go to Top
6031 - COMMUNICATION
CABLE
SPECIFICATION REQUIREMENTS
1) The locations for Communication Cable will be of the type noted on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Communication Cable (Type and Size Specified)" |
LF |
REFERENCE ITEMS
(625)
Go to Top
6032 - HORIZONTAL SIGN
LIGHT
SPECIFICATION REQUIREMENTS
1) The locations for Horizontal Sign Lights will be of the type noted on the
plans.
2) The exterior of the sign light shall be finished with two (2) coats of
Federal yellow
gloss enameland the interior with two (2) coats of white gloss
enamel.
3) The sign light shall be approximately 37 inches long so as to mount under a
three
section 12 inch signal without extending beyond the mounting hardware
of the
signal assembly.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
(616)
Go to Top
6210 INTERNALLY LIGHTED STREET NAME
SIGNS
SPECIFICATION REQUIREMENTS
1) The locations for Internally Lighted Street Name Signs attached to traffic
signal poles will be
as shown on the plans.
2) Signs shall have single side message or double side message as shown on the
plans.
3) The internally lighted street name sign shall be powered from the same
service pole that provides
power to the traffic signal on which the sign is
mounted. Contractor shall install 20 amp circuit
breaker and photocell when necessary.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Internally Lighted Street Name Signs (Type and Size
Specified)" |
EA |
REFERENCE ITEMS
None
Go to Top
6380 - REFLECTORIZED PROFILE PAVEMENT
MARKINGS
SPECIFICATION REQUIREMENTS
1) The locations for Reflectorized Profile Pavement Markings will be of the type
noted on the plans.
2) Type I Profile Markings are thermoplastic type materials that require heating
to elevated
temperatures for application.
3) Type II Profile Markings are paint-type materials that are applied at ambient
or slightly elevated
temperatures.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Reflectorized Profile Pavement Markings
(Type, Color, Size |
LF |
|
and Width Specified)" |
|
REFERENCE ITEMS
(666, 677, 678)
Go to Top
6401 - CLOSED LOOP TRAFFIC SIGNAL
SYSTEM
SPECIFICATION REQUIREMENTS
1) The locations for Closed Loop Traffic Signal System will be as shown on the
plans.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
None
Go to Top
6504 - TESTING, TRAINING, DOCUMENTATION
AND WARRANTY
SPECIFICATION REQUIREMENTS
1) The Engineer will accept certification from an independent testing lab that
the Design Approval
Test has been satisfactorily completed.
2) The Engineer shall be notified a minimum of ten (10) working days before
tests are to
be conducted.
3) The Engineer and/or his representative reserves the right to witness all
tests.
OPTIONAL REQUIREMENTS
None
PAYMENT AND MEASUREMENT
Subsidiary to the various bid items in the contract.
REFERENCE ITEMS
None
Go to Top
6505 - SURVEILLANCE SYSTEM LOOP
DETECTORS
SPECIFICATION REQUIREMENTS
1) The locations for Surveillance System Loop Detectors will be as shown on the
plans.
2) Pavement cuts shall be made to a depth of two (2) inches unless otherwise
shown on the
plans or directed by the Engineer.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Detector Loop (Size Specified)" |
EA |
REFERENCE ITEMS
(684, 688)
Go to Top
6519 - DIGITAL CARD RACK DETECTOR ASSEMBLY
(8 SLOT RACK)
SPECIFICATION REQUIREMENTS
1) The locations for Digital Card Rack Detector Assemblies will be of as shown
on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Detector Unit" |
EA |
2) |
"Detector Card Rack (8 Slot)" |
EA |
3) |
"Power Supply" |
EA |
REFERENCE ITEMS
None
Go to Top
6670
-
PORTABLE CHANGEABLE MESSAGE SIGN
SPECIFICATION REQUIREMENTS
1) The location and operation of of these unit(s) for the
various stages of construction shall be as
indicated under the provisions for traffic handling provided
in the contract, as shown on the plan
details, or as directed by the Engineer.
2) The sign control circuitry shall provide for the permanent storage of a
minimum of 15
pre-programmed messages, the text of which shall be as shown
on the plans.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Portable Changeable Message Signs (Type Specified)" |
DAY |
REFERENCE ITEMS
None
Go to Top
6995 - PREFABRICATED PAVEMENT MARKINGS
WITH WARRANTY
SPECIFICATION REQUIREMENTS
1) The locations and type of Prefabricated Pavement Markings will be noted
on the plans
or as directed by the Engineer.
2) Markings may be placed on roadways either free of traffic or open to traffic.
3) Waste generated by this work shall be removed from the job site before the
end of each
working day.
OPTIONAL REQUIREMENTS
None
|
PAYMENT DESCRIPTION |
UNITS |
1) |
"Pavement Markings with Warranty (Type,
Color, Shape, Size |
LF |
|
and Width Specified)" |
|
REFERENCE ITEMS
(677)
Go to Top
|